diff --git a/doc/uart.md b/doc/uart.md
index b349eb4..6a6d191 100644
--- a/doc/uart.md
+++ b/doc/uart.md
@@ -37,7 +37,7 @@ It uses a fixed serial configuration of 115200 bps, 8 data bits, 1 stop bit, no
 
 
 ## Notes
-A 16 byte FIFO is used when receiving data.
+A 64 byte FIFO is used when receiving data.
 
 When reading data, each byte needs to be acknowledged by writing the _C_ flag to the UART register.
 
diff --git a/pcomp/Makefile b/pcomp/Makefile
index e183f73..4afc3ef 100644
--- a/pcomp/Makefile
+++ b/pcomp/Makefile
@@ -13,7 +13,7 @@ LSYMGEN=./lsymgen
 .pas:
 	fpc -Mobjfpc -gl $<
 
-all: pcomp sasm sdis lsymgen shortgen nativeprogs
+all: libs pcomp sasm sdis lsymgen shortgen nativecomp nativeprogs
 
 libs: pcomp sasm lsymgen shortgen
 	$(SASM) ../lib/coreloader.s
@@ -22,9 +22,9 @@ libs: pcomp sasm lsymgen shortgen
 	$(SASM) ../lib/stdlibwrap.s ../lib/stdlib.lib
 	$(LSYMGEN) ../lib/stdlibwrap.sym ../lib/stdlib.lsym
 
-test: sasm.s pcomp.s lsymgen.s shortgen.s
+test: libs sasm.s pcomp.s lsymgen.s shortgen.s
 
-testprgs: sasm.prog pcomp.prog lsymgen.prog shortgen.prog
+testprgs: libs sasm.prog pcomp.prog lsymgen.prog shortgen.prog
 
 nativecomp: libs pcomp.prog sasm.prog lsymgen.prog shortgen.prog
 
@@ -41,4 +41,5 @@ examples: nativecomp ../tests/readtest.prog ../tests/readchartest.prog ../tests/
 	-$(MAKE) -C ../rogue -f Makefile.tridoracpu
 
 clean:
-	rm -f pcomp sasm sdis libgen lsymgen *.o *.s *.prog
+	rm -f pcomp sasm sdis libgen lsymgen shortgen*.o *.s *.prog \
+		../lib/stdlib.s ../lib/stdlib.lib ../lib/stdlib.lsym
diff --git a/tridoracpu/tridoracpu.srcs/irqctrl.v b/tridoracpu/tridoracpu.srcs/irqctrl.v
index b71df60..5608440 100644
--- a/tridoracpu/tridoracpu.srcs/irqctrl.v
+++ b/tridoracpu/tridoracpu.srcs/irqctrl.v
@@ -1,6 +1,6 @@
 `timescale 1ns / 1ps
 
-module irqctrl #(IRQ_LINES = 3, IRQ_DELAY_WIDTH = 4) (
+module irqctrl #(IRQ_LINES = 3, IRQ_DELAY_WIDTH = 8) (
         input wire clk,
         input wire [IRQ_LINES-1:0] irq_in,
         input wire cs,
diff --git a/tridoracpu/tridoracpu.srcs/stackcpu.v b/tridoracpu/tridoracpu.srcs/stackcpu.v
index 1d929f7..b8ef78c 100644
--- a/tridoracpu/tridoracpu.srcs/stackcpu.v
+++ b/tridoracpu/tridoracpu.srcs/stackcpu.v
@@ -399,7 +399,10 @@ module stackcpu #(parameter ADDR_WIDTH = 32, WIDTH = 32,
     // process irq
     always @(posedge clk)
     begin
-        if(seq_state == MEM && irq_pending && !(ins_xfer & xfer_r2p))   // in FETCH state, clear irq_pending.
+        // in MEM state, clear irq_pending, when nPC has been set to IV
+        // RET instruction is a special case because we need to use
+        // the new PC that is in mem_data
+        if(seq_state == MEM && irq_pending && !(ins_xfer && xfer_r2p))
             irq_pending <= 0;
         else
             irq_pending <= irq_pending || irq;  // else set irq_pending when irq is high
diff --git a/tridoracpu/tridoracpu.srcs/tdraudio.v b/tridoracpu/tridoracpu.srcs/tdraudio.v
index 1629e31..4ad978d 100644
--- a/tridoracpu/tridoracpu.srcs/tdraudio.v
+++ b/tridoracpu/tridoracpu.srcs/tdraudio.v
@@ -233,7 +233,7 @@ module tdraudio #(DATA_WIDTH=32) (
         chan2_rd_data, amp_wr_data,
         chan2_rd_en, chan2_wr_en,
         chan2_amp,
-        chan2_irq, chan2_running);
+        chan2_running, chan2_irq);
 
     wavegen chan3(clk, reset, reg_sel,
         chan3_rd_data, amp_wr_data,
diff --git a/tridoracpu/tridoracpu.srcs/top.v b/tridoracpu/tridoracpu.srcs/top.v
index a4533d2..0dc3346 100644
--- a/tridoracpu/tridoracpu.srcs/top.v
+++ b/tridoracpu/tridoracpu.srcs/top.v
@@ -278,6 +278,9 @@ module top(
                         (io_slot == 4) ? tdraudio_rd_data:
     `endif
                         -1;
+    irqctrl irqctrl0(`clock, irq_in, irqc_cs, mem_write_enable,
+            irqc_seten, irqc_rd_data0,
+            irq);
 
      // CPU -----------------------------------------------------------------
     stackcpu cpu0(.clk(`clock), .rst(rst), .irq(irq),
@@ -288,10 +291,6 @@ module top(
         .mem_wait(mem_wait),
         .debug1(led1), .debug2(led2), .debug3(led3));
 
-    // Interrupt Controller
-    irqctrl irqctrl0(`clock, irq_in, irqc_cs, mem_write_enable,
-            irqc_seten, irqc_rd_data0,
-            irq);
 
     // count clock ticks
     // generate interrupt every 20nth of a second
diff --git a/tridoracpu/tridoracpu.xpr b/tridoracpu/tridoracpu.xpr
index a9dc20f..a3dd3f6 100644
--- a/tridoracpu/tridoracpu.xpr
+++ b/tridoracpu/tridoracpu.xpr
@@ -358,9 +358,7 @@
   <Runs Version="1" Minor="22">
     <Run Id="synth_1" Type="Ft3:Synth" SrcSet="sources_1" Part="xc7a35ticsg324-1L" ConstrsSet="constrs_1" Description="Vivado Synthesis Defaults" AutoIncrementalCheckpoint="false" WriteIncrSynthDcp="false" State="current" Dir="$PRUNDIR/synth_1" IncludeInArchive="true" IsChild="false" AutoIncrementalDir="$PSRCDIR/utils_1/imports/synth_1" AutoRQSDir="$PSRCDIR/utils_1/imports/synth_1" ParallelReportGen="true">
       <Strategy Version="1" Minor="2">
-        <StratHandle Name="Vivado Synthesis Defaults" Flow="Vivado Synthesis 2024">
-          <Desc>Vivado Synthesis Defaults</Desc>
-        </StratHandle>
+        <StratHandle Name="Vivado Synthesis Defaults" Flow="Vivado Synthesis 2024"/>
         <Step Id="synth_design"/>
       </Strategy>
       <GeneratedRun Dir="$PRUNDIR" File="gen_run.xml"/>
@@ -380,9 +378,7 @@
     </Run>
     <Run Id="impl_1" Type="Ft2:EntireDesign" Part="xc7a35ticsg324-1L" ConstrsSet="constrs_1" Description="Default settings for Implementation." AutoIncrementalCheckpoint="false" WriteIncrSynthDcp="false" State="current" Dir="$PRUNDIR/impl_1" SynthRun="synth_1" IncludeInArchive="true" IsChild="false" GenFullBitstream="true" AutoIncrementalDir="$PSRCDIR/utils_1/imports/impl_1" LaunchOptions="-jobs 6 " AutoRQSDir="$PSRCDIR/utils_1/imports/impl_1" ParallelReportGen="true">
       <Strategy Version="1" Minor="2">
-        <StratHandle Name="Vivado Implementation Defaults" Flow="Vivado Implementation 2024">
-          <Desc>Default settings for Implementation.</Desc>
-        </StratHandle>
+        <StratHandle Name="Vivado Implementation Defaults" Flow="Vivado Implementation 2024"/>
         <Step Id="init_design"/>
         <Step Id="opt_design"/>
         <Step Id="power_opt_design"/>
@@ -391,9 +387,7 @@
         <Step Id="phys_opt_design"/>
         <Step Id="route_design"/>
         <Step Id="post_route_phys_opt_design"/>
-        <Step Id="write_bitstream">
-          <Option Id="BinFile">1</Option>
-        </Step>
+        <Step Id="write_bitstream"/>
       </Strategy>
       <GeneratedRun Dir="$PRUNDIR" File="gen_run.xml"/>
       <ReportStrategy Name="Vivado Implementation Default Reports" Flow="Vivado Implementation 2024"/>